RunCam Device Protocol
RunCam Device Protocol may be the serial interaction protocol initially developed when it comes to RunCam separate and analog digital digital cameras.
The protocol itself supports not merely camera that is full menu navigation but in addition triggering recording on separate style digital cameras in addition to interacting the available sd-card room, syncing the existing date, writing towards the osd and switching the camera or wifi function (if available) off and on.
Only a few attributes of the protocol are supported in betaflight but both betaflights help plus the protocol itself have been in continued development.
Recently just like TBS Smartaudio and IRC Tramp other programs (for example Caddx) started initially to adopt support for the protocol inside their digital cameras.
Presently supported features in betaflight
The protocol that is current can be seen right right here:
Supported cameras/devices and procedures
Analog/classic fpv cameras
Any RunCam Camera that supports UART digital digital camera settings should work.
Micro Swift 3, Runcam Racer 2, etc.
RunCam Split cameras (1,2,mini and mini 2 etc.) also work nonetheless might need a firmware upgrade. The very first runcam split delivered with a different sort of protocol – remember to update it in either case as more recent firmwares enhanced different things.
OSD Menu Control
Going into the osd menu to alter settings should make use of the exact same stick commands as FPV Camera Control
Camera Button Simulation (Record/Photo/Wifi/Power Switch)
Firmware: BetaFlight Firmware (≥3.2.0) Configurator computer computer software: Betaflight Configurator (≥3.2.0)
Any available UART software on the BetaFlight
1.Connect the RunCam separate using the UART program regarding the trip Controller
2.Make the Flight Controller recognize the Split
For instance, we connect the separate towards the UART 3 user interface in the BetaFlight: link the journey controller to your computer, open the Betaflight then Configurator. Into the Peripherals line regarding the line UART3 (from the Ports tab), choose RunCam unit and then click Save And Reboot.
3.Instructions regarding the functions of this digital camera and assigning transmitter networks for them
Within the Betaflight Configurator, navigate towards the Modes tab. You will find brand brand new CAMERA WI-FI, CAMERA ENERGY and CAMERA CHANGE modes.
CAMERA WI-FI: turn on/off the WIFI for the digital digital digital camera. When into the OSD regarding the digital camera, it is utilized to verify your selection. CAMERA ENERGY: start/stop the movie. Whenever when you look at the OSD of this digital digital camera, this might be utilized to go towards the next menu product. CAMERA CHANGE MODE: switch among the list of three modes, movie, picture and OSD establishing mode. Whenever into the OSD of this digital digital camera, this may leave the menu. Assign any channel that is available the event you’ll need, as an example:
Assign the AUX1 to your CAMERA WI-FI, range 1900-2100 Assign the AUX2 towards the CAMERA ENERGY, range 1900-2100 Assign the AUX3 towards the CAMERA CHANGE MODE, range 1900-2100
4.Assign the channel towards the switch associated with the controller
Please select your Model regarding the controller, then usage of the Mixer program and designate the channel towards the switch associated with controller. Take opentx 2.2.0 for instance, assign the channels CH5, CH6, and CH7 to SA, SB, SD correspondingly.
Energy the trip Controller plus the RunCam separate
Set the SA to your base, the digital camera turns on/off the WIFI Set the SB to your bottom, the digital digital camera starts/stops the movie Set the SD into the base, the camera switches one of the three modes: video clip, picture and OSD mode that is setting
Caddx Turtle v2
Caddx additionally implemented support for the RunCam Device protocol via their final firmware enhance. Take note but that just the turtle v2 correctly supports UART settings whilst the v1 had some incompatible connections on the board despite having UART pads.
For the v1 you’ll use FPV Camera still Control to go into the OSD and get a handle on the digital digital camera via your transmitter.
Beware that OSD control is disabled during recording.
OSD Menu Control
Going into the menu that is osd alter settings should utilize exactly the same stick commands as FPV Camera Control
Camera Button Simulation (Recording)
Just like the RunCam Split starting/stopping recording on a switch is supported. Stick to the directions outlined above setting it.
Other supported devices
RunCam Control Adapter (OSD Cable Simulation)
The RunCam Control Adapter, which links involving the OSD pin as well as an UART regarding the FC, permits navigation for the OSD menu through the transmitter. Unlike the FPV Camera Control nevertheless no extra resistors or capacitors are needed.
According to the unit some shortcut keys are also supported. As an example keeping roll pressed to towards the right will switch the presently chosen scene when utilizing a Micro Swift2.